Analysis of the Effect of Blade Washing Compressor on Compressor Efficiency and Thermal Efficiency of Gas Turbine at PLTG XXX

Authors

  • Edy Susanto Institut Teknologi PLN
  • Hotdian Sinambela Universitas Sumatera Utara
  • Rafi Tri Khairullah Institut Teknologi PLN

DOI:

https://doi.org/10.32734/dinamis.v13i1.18846

Keywords:

PLTG, heat rate, compressor blade washing

Abstract

The most important parts of a gas power system are the compressor and gas turbine. Compressor performance will naturally decrease due to high ambient temperatures and dirt in the incoming air and make the compressor inefficient. To restore compressor efficiency, it is recommended to clean the compressor using the compressor blade washing method. The purpose of this study was to determine the compressor blade washing procedure used in the PLTG system and determine the parameters tested and analyses their effect on the thermal efficiency of the PLTG. This study was conducted on a PLTG unit operating at a load of 120 MW or 50% of the installed capacity, with research stages including data collection, calculation of the gas turbine heat rate, calculation of the thermal efficiency of the PLTG cycle and calculation of compressor efficiency. From the implementation of the compressor blade washing carried out, there was an increase in compressor efficiency of 2.62% and after the compressor blade washing caused a decrease in the heat rate of 853 kJ / kWh, so that there was an increase in the thermal efficiency of the PLTG of 1.74%.

Downloads

Download data is not yet available.

References

H. Risaldi, and E. Susanto, “Analisa Titik Kebocoran Tube HRSG Berdasarkan Faktor Pengaruhnya PLTGU UP Gresik,” TEKNIKA: Jurnal Teknik, vol 10 pp. 120–126, 2023.

H. Zhang, Y. Jiang, C. Chen, and Y. He, “Simulation of particle deposition on high temperature turbine film cooling blade surface with dynamic mesh morphing.” International Communications in Heat and Mass Transfer. vol. 151, 107244. 2024.

W. Sun, Y. Zheng, J. Zhang, J. Chen, and J. Yu, “Numerical Research Progress on the Particle Deposition Characteristics of Gas Turbine Blade Surface.” Powder Technology. vol. 439, 119679. 2024.

A. Castorrini, P. Venturini, A. Corsini, and F. Rispoli, “Simulation of the deposit evolution on a fan blade for tunnel ventilation.” J. Eng. Gas Turbines Power. vol. 142, 1438. 2020.

W. Sun, Y. Zheng, J. Zhang, J. Chen, and J. Yu. “Numerical study on particle deposition characteristics of turbine blade with cooling film.” Powder Technology. vol. 439, 119679. 2024.

X. Weiwei, Z. Konghao, W. Jianjun, L. Yajun, and L. Qiang, “Modeling and numerical analysis of the effect of blade roughness on particle deposition in a flue gas turbine.” Powder Technology. vol. 347, pp. 59-65. 2019.

M. Anggeraini, C.S. Abadi, and D. Mardiansah, “Analisis Pengaruh Turbine Washing Terhadap Performa Turbin Uap dan Daya Pembangkitan.” Seminar Nasional Teknik Mesin. Politeknik Negeri Jakarta, 2018, pp 553-560.

T. Chen, X. Jia, X. Liu, Y. Tong, H. Zhang, and L. He, “Experimental Research on Water Washing Process of Gas Turbine Blades.” International Conference on Mechanical Engineering, Intelligent Manufacturing and Automation Technology, Guilin, China, 2023, pp 553-560.

J. Xie, Y. Gui, H. Shao, T. Yang, and R. Li, “Research progress on particle deposition characteristics of cooling channel in gas turbine.” Thermal Science and Engineering Progress, vol. 49, 102435. 2024.

E. Ogbonnaya, “Gas Turbine Performance Optimization Using Compressor Online Water Washing Technique.” Engineering, vol. 3, pp. 500-507. 2011.

M. Qi, X. Ren, X. Li, Y. Xiao, and Y. Li, “Performance Investigation of a Large Turning Blade for Marine Gas Turbine Based on Experimental and Numerical Methods.” Machines, vol. 11, 346. 2023.

S. Rahmaniar, B. Puguh, and I. Indriyani, “Analisis Kinerja Turbin Gas pada Pembangkit Listrik Tenaga Gas Unit 4 di PT PLN Indonesia Power Bali PGU,” Surya Teknika, vol 11 pp. 368-370, 2024.

G. Agati, P. Venturini, S. Gabriele, F. Rispoli,and D. Borello, “Effects of Water-to-Air Mass Ratio on Long-Term Washing Efficiency and Erosion Risk in an Axial Compressor Under Online Washing Conditions.” J. Turbomach, vol. 146, 051005. 2024.

L. Cai, J. Yao, Y. Hou, Y. Li, S. Wang, and J Mao, “Numerical Study on Erosion Characteristics of Flue Gas Turbine Blades.” Thermal Science, vol. 27 pp. 4291-4305, 2023.

B. Setiawan, G. Hidayat dan S. D. Cahyono, “Analisis Pengaruh Compressor Washing Terhadap Efisiensi Kompresor dan Efisiensi Thermal Turbin Gas Blok 1.1 PLTG UP Muara Tawar,” Jurnal Mesin Teknologi (SINTEK Jurnal), vol. 11, no. 1, pp. 49-54, Juni 2017.

Downloads

Published

2025-06-30

Issue

Section

Articles