Pengaruh Oleamida Terhadap Karakteristik Pematangan Karet Alam Terisi Silika

Indra Surya; Philbert

doi:10.32734/jtk.v10i2.6606

Authors

Indra Surya Universitas Sumatera Utara
Philbert Universitas Sumatera Utara

DOI:

https://doi.org/10.32734/jtk.v10i2.6606

Keywords:

natural rubber, oleamide, silica, curing characteristic, torque

Abstract

The purpose of this study was as a feasibility study of the utilization of oleamide as a new additive for natural rubber (NR) filled with silica using the semi-efficient vulcanization system. Silica fillers used as much as 30 parts per hundred parts rubber (phr). Oleamide was obtained from the synthesis of oleic acid with urea. Oleamide was inserted into the silica filled NR compounds with the varied composition of 0.0 phr; 2.0 phr; 4.0 phr; 6.0 phr, and 8.0 phr. The influence of oleamide on the curing characteristic of the silica filled NR compounds was observed. It was obtained that the oleamide functions as a curative and also a plasticizer. The greater the levels of oleamide added, the shorter the scorch time and optimum curing time were. Oleamide also decreased the minimum torque with addition up to 8.0 phr. The greater the levels of oleamide was, the lower the minimum torque was. Oleamide also increased the maximum torque and torque difference of the silica-filled NR composites at the addition of 2.0 phr. The 2.0 phr was the optimum composition of the oleamide.

Downloads

Download data is not yet available.

References

Y. Wei, H. Zhang, L. Wu, L. Jin, and S. Liao, “A review on characterization of molecular structure of natural rubber,” MOJ Polym. Sci., vol. 1, no. 6, pp. 197–199, 2017.

M. Akiba and A. S. Hashim, “Vulcanization and crosslinking in elastomers,” Prog. Polym. Sci., vol. 22, no. 3, pp. 475–521, 1997.

B. Huneau, “Strain-induced crystallization of natural rubber : A review of X-ray diffraction investigations,” Rubber Chem. Technol., vol. 84, p. 425−452, 2011.

R. W. Sianturi and I. Surya, “Pengaruh penambahan lauril alkohol terhadap sifat-sifat uji tarik komposit karet alam terisi silika,” J. Tek. Kim. USU, vol. 7, no. 1, pp. 48–53, 2018.

A. I. Al-Mosawi, M. M. Ali and J. H. Mohmmed, “Experimental approach to mechanical properties of natural rubber mixing with calcium carbonate powder,” Int. J. Phys. Sci., vol. 7, no. 49, pp. 6280–6282, 2012.

K. Rajkumar, P. Ranjan, P. Thavamani, P. Jeyanthi, and P. Pazhanisamy, “Dispersion studies of nanosilica in nbr based polymer nanocomposite,” Rasayan J. Chem., vol. 6, no. 2, pp. 122–133, 2013.

P. Raju, V. Nandanan, and S. K. N. Kutty, “A study on the use of linseed oil as plasticiser in natural rubber compounds,” J. Rbber Res., vol. 11, no. 3, pp. 147–162, 2008.

L. M. Tirtayasa, “Pra rancangan pabrik pembuatan oleamida dari asam oleat dan urea dengan kapasitas produksi 10.000 ton/tahun,” Skripsi, Universiats Sumatera Utara, Medan, 2012.

M. Pishvaei and F. F. Tabrizi, “Synthesis of high solid content polyacrylate/nanosilica latexes via miniemulsion polymerization,” Iran. Polym. J., vol. 19, no. 9, pp. 1–12, 2010.

S. Prasertsri and N. Rattanasom, “Mechanical and damping properties of silica/natural rubber composites prepared from latex system,” Polym. Test., vol. 30, no. 5, pp. 515–526, 2011.

M. H. Harandi, F. Alimoradi, G. Rowshan, M. Faghihi, M. Keivani, and M. Abadyan, “Morphological and mechanical properties of styrene butadiene rubber/nano copper nanocomposites,” Results Phys., vol. 7, pp. 338–344, 2017.

A. Das, K. W. Stöckelhuber, R. Jurk, D. Jehnichen, and G. Heinrich, “A general approach to rubber-montmorillonite nanocomposites: Intercalation of stearic acid,” Appl. Clay Sci., vol. 51, no. 1–2, pp. 117–125, 2011.

P. L. Teh, Z. A. M. Ishak, A. S. Hashim, J. Karger-Kocsis, and U. S. Ishiaku, “Effects of epoxidized natural rubber as a compatibilizer in melt compounded natural rubber-organoclay nanocomposites,” Eur. Polym. J., vol. 40, no. 11, pp. 2513–2521, 2004.

H. L. Tampubolon, D. S. Hutapea, and I. Surya, “Pengaruh penambahan alkanolamida terhadap karakteristik pematangan dan kekerasan vulkanisat karet alam berpengisi silika,” J. Tek. Kim. USU, vol. 1, no. 1, pp. 7–10, 2012.

Y. Widyanata, I. M. S. Sitorus, and I. Surya, “Pengaruh penambahan alkanolamida terhadap sifat-sifat uji tarik vulkanisat karet alam berpengisi kaolin,” J. Tek. Kim. USU, vol. 2, no. 4, pp. 1–5, 2013.